MacroSystem Digital Video HDV-Recorder Manual de usuario descargar pdf (Pagina 36)

Chapter 4

Rest: The ﬁeld Rem. shows you how much time remains,

meaning how much video can still be recorded. This amount is

an estimate. This is especially the case for longer recordings or

for HD footage, because the system calculates the remaining

time on the basis of the level of detail of the footage already

recorded. The value is not recalculated until the current record-

ing is ﬁnished. If the quality settings change, the actual space

may be slightly more or less than this estimate.

Just like the video settings, this menu is superimposed

over the video. You can see the video during recording

and thus always decide whether you want to digitize a se-

quence or not. The symbol at the bottom left with the two

triangles moves the panel to the top edge of the screen. This is

useful if the panel happens to be covering important parts of

your material.

You can use the button above it to reduce the menu to a

much smaller bar, in case too much of your video image has

been covered. Then the only buttons available is the button

described above and the button (Recording menu symbol) to

restore the entire menu.

’DV control’ is done with these

ﬁve buttons. You can directly

control the connected DV device through the i-Link interface.

You should be aware that most devices are compatible, but

some are not. If this is the case, the DV/HDV device can be

started manually and should then input correctly. Seen from

left to right, the buttons are used to: stop the recorder, play,

pause, rewind, and fast forward. Rewind and fast forward have

three different effects. Fast rewind and fast forward are

achieved while the DV source is in stop mode, viewable slow

rewind and slow forward in play back mode, and frame-by-

frame backward and forward in pause mode.

The four menu symbols bring you

directly to the Edit, Record/Edit, Video

settings, and to the Main menu screens.

4.7 Editing

This screen is used for most of your editing work, and for se-

quencing of trimmed scenes. This is the most important menu.

The view of the scene bin can also be modiﬁed or deﬁned in

the menu under Settings-Storyboard, Timeline.

The menu can be displayed in different ways. The display de-

pends on the screen resolution and also depends on whether

you are using the Timeline or the Storyboard modes. Resolu-

tions higher than 1024x768 pixels (1280x720 for a 16:9 project)

will result in a slightly different edit bin screen section. All but-

tons described here are present in both view types.

(1) The Storyboard is displayed in the top third of the Edit

menu. This is a tool that has been used since movies were

invented. The idea is to clearly lay out all the scenes of a pro-

duction in order to more easily implement editing principles. A

single frame, (the ﬁrst pictures of a scene), are used as sym-

bols (‘thumbnails’) to represent the scene. A glimpse at the

storyboard allows you to grasp the whole story without having

to review all of the material. Traditionally, the storyboard was

a large board composed of hand-drawn pictures. Your system

uses an electronic storyboard.

Scenes are selected from the scene bin and put into order on

the storyboard, located in the upper section of the screen. In

the storyboard the selected scene is in the center. The se-

lected scene length (duration) is displayed above the scene

to highlight it. If you insert a new scene in the storyboard, it

will be inserted just after the current scene. If there is only one

scene in the storyboard, however, you will, only in this case, be

able to determine whether the next scene must be inserted in

front of or after this scene. Clicking on a scene in the story-

board causes it to be moved to the center (often referred to

as the ‘selected’ or ‘active’ scene). Depending on the chosen

resolution (see chapter 5: VGA mode), at least seven complete

scenes will ﬁt into a visible part of the Storyboard. But there is

no limit to the number of scenes that may actually be present

on the storyboard. The storyboard can be scrolled to the left

or right. The starting point is to the left, and scenes are played

sequentially from left to right.

To scroll up or down in the scene bin, you can use the scroll-

bar on the right or the arrow button below. It is even faster

1 2 ... 31 32 33 34 35 36 37 38 39 40 41 ... 111 112

Comentarios a estos manuales

Sin comentarios

MacroSystem Digital Video HDV-Recorder Manual de usuario Pagina 36

Comentarios a estos manuales

Relacionado con productos y manuales para Grabadores de vídeo digital (dvr) MacroSystem Digital Video HDV-Recorder